Bath Center Fuel Steam Atmospheric Pressure Boiler Price
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
The higher this ratio, the more efficient is the boiler. In the majority of cases, high pressure boilers have an 85% fuel to steam efficiency. Stack Temperature and Losses: Stack temperature is temperature that is lost from the combustion of the gas in a boiler. An efficient boiler uses as much of the heat from the combustion as possible.Get Price
The boiler efficiency of modern pulverized fuel, hard coal-fired units is 94%–95% (LHV basis), reducing slightly to 90%–91% for lignite-fired units due to the higher moisture content. When combined with the other elements of the Rankine cycle, the overall efficiency currently achievable in conventional plants is in the 40%–45% range.Get Price
The off-gas at a rate of 66,000 Nm3/h leaves the afterburner chamber at a temperature of 1000°C. Heat is recovered in a steam boiler. The gases leave the boiler at 270°C. Steam is generated at 25 atm and superheated to 250°C at a rate of 34 t/h. A steam turbine generates electric power at the rate of 1320 kw/h consuming 22 t/h steam.Get Price
7.4 Fluid pressure measurement 164. 7.5 Liquid flow measurement 165 resistant to water and atmospheric corrosion. Used for boiler fitting, bushes, bearings, glands etc. Copper and tin (Bell metal): Copper 80% and tin 20%. Hard and resistant to surface wear. Creep failure is an important phenomenon for steam and chemical plants which Get Price
Regardless of whether the draft regulator is serving an oil fired heating boiler or an oil fired water heater, soot coming out of the barometric damper or out of the flue vent pipe, or the presence of soot and burn marks on the heater, or even noises: stumbling, rumbling, noisy oil burners, as well as odors, are examples of improper oil burner Get Price
D Steam leaves an industrial boiler at 827.4 Kpa and 171.6 deg. C. A portion of the steam is passed through a throttling calorimeter and is exhausted to the atmosphere when the calorimeter pressure is 101.4 Kpa. How much moisture does the steam leaving the boiler contain if the temperature of the steam at the calorimeter is 115.6 Deg. C.Get Price
D Steam leaves an industrial boiler at 827.4 Kpa and 171.6 deg. C. A portion of the steam is passed through a throttling calorimeter and is exhausted to the atmosphere when the calorimeter pressure is 101.4 Kpa. How much moisture does the steam leaving the boiler contain if the temperature of the steam at the calorimeter is 115.6 Deg. C.Get Price
Nov 07, 2016 · Indirect-fired units may use different sources for heat: hot water or steam from a boiler, steam from district heating, or waste heat in the form of water, air, or other gas. Absorption chillers can be single-effect or double-effect, where one or two vapor generators are used.Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
